Jump to content

Problem With GPSMAP 64s and Multi's


BikeBill

Recommended Posts

I've been really pleased with my 64s but I think I've found a bug. In the Geocaching profile the unit has the ability to let me input the additional stages of a multi-cache but the GPS will either freeze or show a gray screen when I try to do this. It doesn't misbehave all the time but will most often do it when I am entering stages beyond the second.

 

I hadn't done many multi's lately but today I did a 4-stage and had the unit freeze several times. It happens just as I put in the last digit of the coord's and hit okay. Then the only way to un-freeze it is to pop out the batteries. Then I have to pull up the cache and input the extra stage all over again.

 

Has anyone else had a problem like this on their 64 series? Any solutions? And does someone know the most effective way to communicate with Garmin about problems like this?

Link to comment

Bill, I've not had crashes with multis and my 64s, but I use a different method than you do.

I always use the Mark Waypoint button to enter the next waypoint(s) in a multi. It's an old habit, carried over from a previous device. But it's just as easy as 'enter next stage', I think. Never had a crash doing it that way.

Link to comment

Bill, I've not had crashes with multis and my 64s, but I use a different method than you do.

I always use the Mark Waypoint button to enter the next waypoint(s) in a multi. It's an old habit, carried over from a previous device. But it's just as easy as 'enter next stage', I think. Never had a crash doing it that way.

 

I think if you put it in as a waypoint you will have to change your compass dashboard....I normally use the geocaching detail dashboard but I change it if I put a cache in as a waypoint ( for a puzzle or multi ) so the needle will point to my waypoint and not the next closest cache on my list.

Link to comment

Bill, I've not had crashes with multis and my 64s, but I use a different method than you do.

I always use the Mark Waypoint button to enter the next waypoint(s) in a multi. It's an old habit, carried over from a previous device. But it's just as easy as 'enter next stage', I think. Never had a crash doing it that way.

 

I think if you put it in as a waypoint you will have to change your compass dashboard....I normally use the geocaching detail dashboard but I change it if I put a cache in as a waypoint ( for a puzzle or multi ) so the needle will point to my waypoint and not the next closest cache on my list.

Yes, that's correct. For that reason I never use the Geocaching dashboard.

Link to comment

I was out today and did some two stage caches. The second set of coord's loaded fine. Just to test the unit, I entered a third set twice. Both times it froze the unit like before. It either freezes the current screen or goes to a 'gray screen' and locks up. Either way, I have to pop a battery out to re-boot.

 

I wonder if I have a defective 64s or if it's a bug. I was hoping someone here could tell me if they've encountered the same thing. I like to use the Geocaching profile and think the unit should work as intended.

Link to comment

Does a 64 "remember" the coordinates for each WP you put in "Next stage"?

If not then there's an even better reason for marking WPs.

 

I only use the geocaching dashboard when going for a traditional or mystery with corrected coordinates. All other times I use "small datafields" with Distance to destination, Trip odometer, avg. total speed and speed.

 

This is on an Oregon 600 but I guess a 64 has similar software.

Link to comment

I was out today and did some two stage caches. The second set of coord's loaded fine. Just to test the unit, I entered a third set twice. Both times it froze the unit like before. It either freezes the current screen or goes to a 'gray screen' and locks up. Either way, I have to pop a battery out to re-boot.

 

I wonder if I have a defective 64s or if it's a bug. I was hoping someone here could tell me if they've encountered the same thing. I like to use the Geocaching profile and think the unit should work as intended.

 

I have the GPSMAP 64, software version 4.

 

I normally use the "small datafields" dashboard and the GPS DOES freeze up when entering a second new waypoint. It does not (so far)exhibit this bug when using the "geocaching" dashboard.

Link to comment

Okay. I just tried entering four or five next stage waypoint on a multi and had no problem. Tried from the map screen and the geocaching and geocaching detail dashboard. Used direct routing. No lockups. Like I say, rule out a bad GPX first. All it takes is one bad cache somewhere on the unit.

Link to comment

Dragging up an old topic here. It's been nearly a couple years since I originally posted my complaint about my 64s locking up when loading more than one additional waypoint for a multi. Has anyone found a way to fix or get around the problem? I haven't had my 64s lock up like that since, let me think, TODAY! Twice!

Link to comment
On 4/18/2017 at 8:17 PM, BikeBill said:

Dragging up an old topic here. It's been nearly a couple years since I originally posted my complaint about my 64s locking up when loading more than one additional waypoint for a multi. Has anyone found a way to fix or get around the problem? I haven't had my 64s lock up like that since, let me think, TODAY! Twice!

Are you using the "enter next stage" feature? If so, stop. I always just create a waypoint for subsequent stages of a multi. I've never had a problem with that method on my 64st.

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...